Hitachi BE-IR30 Manuel d'utilisateur

Please read this operation Guide carefully for proper operation, and keep it for future refernce.BE-IR30 / 31Infrared B/W Camera ModuleOperation Guide

6. External viewBE-IR30 / 319Lens19.2 ± 0.5(C-mount)1.4 ± 0.2CCDBase plateImaging faceLens-mountExtension of optical path dueto the thickness of CCD

8. InstallationBE-IR30 / 3110 When installing the camera in a housing or unit of equipment, secure with two M2 screwsinserted into the 2.5 mm diamet

9. Typical connectionBE-IR30 / 3111BE-IR30Image processor orVideo monitorRegulated power supply(More then 300 mA)Note1 : • When more than one video

9. Typical connectionBE-IR30 / 3112BE-IR31Image processor orVideo monitorRegulated power supply(More then 300 mA)Note1 : • When more than one video

10. External sync (BE-IR31)BE-IR30 / 3113Supply sync signals (HD and VD) for BE-IR31 operation. Refer to connection on page 12.z Horizontal and

11. Function setting and changesBE-IR30 / 3114When changing the function settings , perform the work with thorough care. Be sure to useanti-stati

11. Function setting and changesBE-IR30 / 311511-2 Gamma responseThe factory setting is gamma on. If necessary , the gamma response can be change

11. Function setting and changesBE-IR30 / 311611-3 Auto electronic shutter on / offFactory setting for auto electronic shutter is off. If nec

11. Function setting and changesBE-IR30 / 311711-4 Changes to fixed shutter modeThe fixed shutter mode can be changed by replacing the chip part

11. Function setting and changesBE-IR30 / 311811-5 BE-IR30 external syncThe BE-IR30 factory setting is for internal sync. If required, this can

Table of ContentsBE-IR30 / 3111. Introduction ･･･････････････････････････････････････････   22. General･････････････････････････････････････････････

11. Function setting and changesBE-IR30 / 311911-6 BE-IR31 internal syncThe BE-IR31 factory setting is for external sync. If required, this can

11. Function setting and changesBE-IR30 / 312011-7 HD and VD output (BE-IR30 only)The BE-IR30 can be provided with horizontal and vertical drive

12. OptionsBE-IR30 / 3121LA-IR20 Mount adapter dimensionsRemove c-mount attachment to use as cs-mount.

12. OptionsBE-IR30 / 3122BE-IR30A/31A and LA-IR20 combined dimensions

12. OptionsBE-IR30 / 3123BE-IR30C/31C and CS mount adapter (option) combined dimensions

BE-IR30 / 3124Spectral sensitivity (typical example)10.90.80.70.60.50.40.30.20.10 400 500 600 700 800 900 1000

BE-IR30 / 3125CautionThe specifications of this equipment are subject to change without notice for improvement.Prior to placing your order , be sure t

1. IntroductionBE-IR30 / 312Thank you very much for your purchase of the Hitachi BE-IR30/31 Black and White CameraModule.Prior to using this camera

4．．．．SpecificationsBE-IR30 / 313 2) Sensing area EIA : 6.00(H)×4.96(V)mm CCIR : 6.00(H)×4.96(V)mm3) Signal format Conforming to EIA or CCIR.4)

4．．．．SpecificationsBE-IR30 / 314 21) Standard lens f3.8 (BE-IR30B/31B only)Focal distance f 3.8 mmF value 2.0H 70.9Picture angleV 52.921) Dimensions

5. Notes to usersBE-IR30 / 315 Power supplyz Connect a 9V DC voltage (8.5 to 9.5V) from an external regulated DC power supply.z Use a stable power

5. Notes to usersBE-IR30 / 316  Phenomena inherent to CCD imaging device Following are phenomena inherent to a CCD imaging device , and not defects.

6. External viewBE-IR30 / 317BE-IR30B/31B

6. External viewBE-IR30 / 318BE-IR30C/31C